brother-hl-l3210cw 2020-06-12T15:17:34+00:00
  • Home »
  • Brother HL L3210CW

Brother HL L3210CW Setup

Carry out the below-mentioned steps on the Brother HL L3210CW setup.

Choosing a location for your Brother HL-L3210CW printer:

  •   Make sure that you have enough room for opening the trays, covers, and doors of your printer.
  •   Select a location that is close to an electrical outlet for placing the printer.
  •   Ensure that you keep the printer on a flat, stable surface.
  •   Keep your printer clean, dry, and free of dust.
  •   Please avoid placing it in direct sunlight or extreme temperatures.

Shifting to a different location:

  •   You might have to shift your printer to a different location. To do that, at least two persons are required.
  •   Please handle the printer carefully while transferring it to another location.

Hardware Setup:

  •   After you unpack your Brother HL-L3210CW printer, please check if all the components are available in the printer package.
  •   Remove all the packing materials. Then, you have to re-install the drum unit and the toner cartridge assembly. To do the same, please follow the steps here:
  •   Take out all the blue packing tape.
  •   Next, slide all of the eight drum locks. These drum locks will be in yellow.
  •   Now, take out the orange part from each one of the cartridges.
  •   Push the cartridges firmly into the printer.
  •   You can now start loading paper into the paper tray.
  •   Make sure to adjust the paper guides.
  •   Also, ensure that you do not exceed the maximum paper mark.
  •   Use this procedure to configure the Brother HL L3210CW setup.

Turning on your printer:

  •   First, connect one end of the power cable to your printer. Next, plug the other end into an electrical outlet.
  •   You can now turn on the printer.

Choosing your language (if required):

If you are using an LCD model:

  •   You can press the Up or Down arrow key to choose [Initial Setup]. Press OK after the selection.
  •   Next, select [Local Language] and then press OK. Choose the desired language. Press OK.
  •   Press Cancel.

If you are using a Touchscreen model:

  •   On the touchscreen of your Brother printer, press [Settings]. Then, go to [All Settings].
  •   Select the [Initial Setup] option.
  •   Choose [Local Language].
  •   Press the desired language.
  •   Finally, press the Home button.

The next step is to connect either your computer or your mobile to the Brother printer. Once you have selected the device that is to be connected, you can easily and quickly connect it to your Brother printer.

Once you have completed the hardware setup, the very next step is to perform the software setup.

Software Setup:

  •   You can install the printer driver software either by using the CD that came along with your printer or by downloading the driver software online.
  •   You have now successfully finished the hardware and software of your Brother HL L3210CW setup.

Brother HL L3210CW Driver Download

To download the driver for your Brother HL-L3210CW printer, click the Driver Download button on this site. Else, download the driver from the official Brother site by following the steps below.

  •   First, navigate to the official site of your Brother HL-L3210CW printer.
  •   From the tabs provided on the left pane, click the Downloads tab.
  •   On the Downloads page that displays next, under ‘STEP 1: Select OS Family,’ choose the desired operating system.
  •   Under ‘STEP 2: Select OS Version,’ choose the specific version of the operating system that you have selected under STEP 1.
  •   For instance, if you select the Windows option under STEP 1, and Windows 8.1 (64-bit) under STEP 2, and then click on the OK button, you will be taken to the page where you can view the following items:
  •   Full Driver & Software Package
  •   Drivers
  •   Utilities
  •   Management Tool
  •   Firmware
  •   Note: At times, your operating system and its version will be automatically selected for you.
  •   You can either download the Windows 8.1 (64-bit) under STEP 2, or download a specific driver by going to the Drivers section.
  •   You just have to click the link that is provided in blue. Then, you will find yourself on the Printer Driver page. Here, you can see the End-User License Agreement.
  •   Once you click the Agree to the EULA and Download button, your driver will get downloaded.
  •   You have now successfully downloaded the driver for your Brother HL L3210CW setup.

Brother HL L3210CW Mac Driver

To download the driver for your Mac, you can make use of the steps given here:

  •   First, navigate to the official site of your Brother HL-L3210CW printer.
  •   From the tabs provided on the left pane, click the Downloads tab.
  •   On the Downloads page that appears next, under STEP 1: Select OS Family, select the Mac option.
  •   Under STEP 2: Select OS Version, choose the desired version of Mac. For example, if you choose macOS (10.15) as your version, and click on the OK button, you will find the following list of items:
  •   Full Driver & Software Package
  •   Drivers
  •   Utilities
  •   Firmware
  •   You can either download the Full Driver & Software Package or download the Printer Driver under the Drivers section.
  •   You just have to click the link that is provided in blue. Then, you will find yourself on the Printer Driver page. Here, you can see the End-User License Agreement.
  •   Once you click the Agree to the EULA and Download button, your driver will get downloaded.
  •   You have now successfully downloaded the driver for your Mac.
  •   Follow these steps to configure the Brother HL L3210CW setup.

Brother HL L3210CW Manual Download

To download the manual for your Brother HL-L3210CW printer, please follow the instructions provided below:

  •   Navigate to the official site of your Brother HL-L3210CW printer.
  •   From the tabs provided on the left pane, click the Manuals.
  •   On the Manuals page that appears next, from the drop-down provided for the Language filed, select English. Sometimes, the language will be automatically selected.
  •   Now, you will see the following sections on your screen:
  •   User’s Guide
  •   Setup Guide
  •   Additional Feature Guide
  •   Appendix
  •   You can now choose any of the options given under one of the above guides.
  •   Next, click the blue Download button that is provided opposite to the guide you are choosing.
  •   Then, carry out the on-screen instructions to finish downloading the desired guide or manual.
  •   You have now successfully downloaded the manual or guide for your Brother HL L3210CW setup.
Brother HL L3210CW Manual Download

Brother HL L3210CW Wifi Setup

For the Wi-Fi setup of your Brother HL-L3210CW printer, please carry out the instructions given below:

  •   The first step is to install the driver on your Brother printer.
  •   When you come to the screen where you select your Connection Type, choose the Wireless Network Connection (Wi-Fi) option. Click the Next button.
  •   When the ‘Detecting Existing Wireless Network Settings’ window pops up, verify your Network Name and then click the Next button.
  •   In most of the cases, the setup wizard will automatically apply all your wireless settings and then connect your printer to the network.
  •   If, for some reason, the setup wizard is not able to connect your printer to the network automatically, you have to use alternate methods of connection.
  •   When you face the Enable the Wireless Connection window, you should go to your printer control panel.
  •   Start by pressing the Wi-Fi button on the control panel. When prompted for confirmation, press the Up arrow.
  •   Your Brother printer will now begin retrieving the network settings from your computer. Please follow the instructions until you come to the part where you will be requested to enter your SSID (or Network Name) and Network Key. You can locate these details at the bottom of your router.
  •   At times, you might have to enter the Network Key manually using the printer control panel.
  •   Now, go to the printer control panel. Enter your Network Key by using the arrow buttons and the OK button.
  •   Once you have entered the Network Key, verify if it is correct.
  •   After you have applied all your settings, go to your computer.
  •   In the Configure manually from the control panel window, click on the Next button.
  •   In the Confirm the WLAN configuration window, select the checkbox next to the Checked and confirmed option. Then, click on the Next button.
  •   Once you have connected your Brother printer to the wireless network, you can proceed with the Brother HL L3210CW setup process.

Brother HL L3210CW Airprint

AirPrint is a unique printing solution that has been specially designed for Apple operating systems. It lets you print pictures, emails, and documents wirelessly from any iOS device or a Mac without having to install a driver.

Before you start using AirPrint on macOS, please follow the instructions provided here:

  •   First, you have to add Brother HL-L3210CW to the printer list on your Mac before you begin printing. To do the same, you can make use of the following steps.
  •   On your Mac, navigate to the Apple menu and then choose the System Preferences option.
  •   Next, click on Printers & Scanners.
  •   Below the Printers pane on your left, you will find the Plus (+) icon. Click this icon.
  •   Now, the Add screen will be displayed.
  •   You can now choose your Brother HL-L3210CW printer and then go to the Use pop-up menu. From this menu, select the AirPrint option.
  •   Finally, click on the Add button.
  •   Now, let us see how you can perform printing using AirPrint from any iOS device and a Mac computer.
  •   Perform these steps to configure the Brother HL L3210CW setup.
Brother Hl l3210cw Airprint

Printing using AirPrint from an iPhone, iPad, or iPod touch:

We will be taking Safari as an example of using AirPrint. The procedure used to print might vary from one application to another. Now, please carry out the instructions given here:

  •   First, confirm that your Brother printer is turned on.
  •   Next, on your iOS device, make use of Safari to open the page that you wish to print.
  •   Tap the Share icon.
  •   Now, tap the Print option.
  •   Ensure that your Brother printer is selected. In case no printer has been selected, or a different one (other than your printer model) has been chosen, please follow these steps:
  •   Tap the Printer option on your iOS device.
  •   A list of available printers will now display on your screen.
  •   From this list, select your Brother HL-L3210CW printer.
  •   Now that your Brother HL-L3210CW printer is chosen, you can start setting the desired options. These options will include the number of pages that you need to print.
  •   Finally, tap Print.

Printing using AirPrint from macOS:

Here also, we are going to take Safari as an example. The procedure used to print might vary from one application to another.

Before you begin with the printing, you have to confirm that your Brother printer is available on the list (of printers) on your Mac. When you have done that, you can carry out the following instructions:

  •   Next, on your Mac, make use of Safari to open the page that you wish to print.
  •   Click the File menu and choose the Print option.
  •   Click the Printer pop-up menu.
  •   From the menu, select your Brother HL-L3210CW printer. You can start setting the desired options.
  •   Finally, click Print.
  •   Proceed these steps to configure the Brother HL L3210CW setup.

We have now seen how to use the AirPrint feature on an iOS device and a Mac computer/device.

Brother HL L3210CW Paper Jam

If the loaded paper gets jammed in the manual feed slot, please carry out the steps given here:

  •   Take out the paper that is jammed in or around the printer’s manual feed slot. You have to do this task gently.
  •   Then, reload the paper into the manual feed slot.
  •   To resume printing, press the Go option.
  •   In case the paper gets jammed in the paper tray of your Brother printer, refer to the steps that follow to resolve the issue:
  •   First, pull the paper tray out of your Brother printer.
  •   Next, pull out the jammed paper gently and slowly.

Note: To remove the paper more easily, you can pull it downward with both your hands.

  •   You now have to fan the paper stack. This action will help in avoiding further jams.
  •   Now, slide the paper guides gently in such a way that they fit the paper size.
  •   Confirm that the paper is below the maximum mark.
  •   Finally, insert the paper tray firmly back into your Brother printer.

If you having any further queries regarding the Brother HL L3210CW setup. Click the call button available on the screen.


G
E
T
S
U
P
P
O
R
T